18650 lithium ion battery 3.7v

　　Analysis of 18650 lithium ion battery 3.7vcircuit working principle

　　How 18650 lithium ion battery 3.7vcircuit works

　　The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:

　　1. Normal state

　　Under normal conditions, the "CO" and "DO" pins of N1 in the circuit both output high voltage, and both MOSFETs are in the on state. The 18650 lithium ion battery 3.7vcan charge and discharge freely. Since the on-resistance of the MOSFET is very small, usually less than 30 milliohms, so its on-resistance has little impact on the performance of the circuit. 7|The current consumption of the protection circuit in this state is μA level, usually less than 7μA.

　　2. Overcharge protection

　　The charging method required for lithium-ion batteries is constant current/constant voltage. In the early stage of charging, constant current charging is used. As the charging process progresses, the voltage will rise to 4.2V (depending on the positive electrode material, some batteries require a constant voltage value of 4.1V ), switch to constant voltage charging until the current becomes smaller and smaller. During the charging process of the battery, if the charger circuit loses control, the 18650 lithium ion battery 3.7vvoltage will continue to be charged with constant current after it exceeds 4.2V. At this time, the 18650 lithium ion battery 3.7vvoltage will continue to rise. When the 18650 lithium ion battery 3.7vvoltage is charged to exceed 4.3V, the 18650 lithium ion battery 3.7vchemistry will Side reactions will be aggravated, causing 18650 lithium ion battery 3.7vdamage or safety issues.

　　In a 18650 lithium ion battery 3.7vwith a protection circuit, when the control IC detects that the 18650 lithium ion battery 3.7vvoltage reaches 4.28V (this value is determined by the control IC, different ICs have different values), its "CO" pin will change from high voltage to zero voltage. V2 is turned from on to off, thus cutting off the charging circuit and preventing the charger from charging the battery, thus serving as overcharge protection. At this time, due to the existence of the body diode VD2 of V2, the 18650 lithium ion battery 3.7vcan discharge the external load through this diode.

　　There is still a delay time between when the control IC detects that the 18650 lithium ion battery 3.7vvoltage exceeds 4.28V and sends the shutdown V2 signal. The length of this delay time is determined by C3 and is usually set to about 1 second to avoid errors caused by interference. judge.

　　3. Over-discharge protection

　　When the 18650 lithium ion battery 3.7vis discharging an external load, its voltage will gradually decrease with the discharge process. When the 18650 lithium ion battery 3.7vvoltage drops to 2.5V, its capacity has been completely discharged. At this time, if the 18650 lithium ion battery 3.7vis allowed to continue discharging the load, it will cause damage to the battery. Permanent damage.

　　During the 18650 lithium ion battery 3.7vdischarge process, when the control IC detects that the 18650 lithium ion battery 3.7vvoltage is lower than 2.3V (this value is determined by the control IC, different ICs have different values), its "DO" pin will change from high voltage to zero voltage, causing V1 From on to off, the discharge circuit is cut off, so that the 18650 lithium ion battery 3.7vcan no longer discharge the load, which plays the role of over-discharge protection. At this time, due to the existence of the body diode VD1 of V1, the charger can charge the 18650 lithium ion battery 3.7vthrough this diode.

　　Since the 18650 lithium ion battery 3.7vvoltage cannot be reduced in the over-discharge protection state, the current consumption of the protection circuit is required to be extremely small. At this time, the control IC will enter a low power consumption state, and the power consumption of the entire protection circuit will be less than 0.1μA.

　　There is also a delay time between the control IC detecting that the 18650 lithium ion battery 3.7vvoltage is lower than 2.3V and sending the shutdown V1 signal. The length of this delay time is determined by C3 and is usually set to about 100 milliseconds to avoid errors caused by interference. judge.

　　4. Overcurrent protection

　　Due to the chemical characteristics of lithium-ion batteries, the 18650 lithium ion battery 3.7vmanufacturer stipulates that the maximum discharge current cannot exceed 2C (C=18650 lithium ion battery 3.7vcapacity/hour). When the 18650 lithium ion battery 3.7vis discharged with a current exceeding 2C, it will cause permanent damage to the 18650 lithium ion battery 3.7vor safety issues.

　　During the normal discharge process of the 18650 lithium ion battery 3.7vto the load, when the discharge current passes through two MOSFETs connected in series, a voltage will be generated at both ends due to the on-resistance of the MOSFETs. The voltage value U=I*RDS*2, RDS is a single MOSFET conduction resistance, the "V-" pin on the control IC detects the voltage value. If the load is abnormal for some reason, the loop current increases. When the loop current is large enough to make U>0.1V (this value is determined by The control IC determines that (different ICs have different values), its "DO" pin will change from high voltage to zero voltage, causing V1 to turn from on to off, thereby cutting off the discharge loop and making the current in the loop zero. Plays the role of over-current protection.

　　There is also a delay time between the control IC detecting the occurrence of overcurrent and sending the shutdown V1 signal. The length of this delay time is determined by C3, usually about 13 milliseconds, to avoid misjudgment caused by interference.

　　From the above control process, it can be seen that the overcurrent detection value not only depends on the control value of the control IC, but also depends on the on-resistance of the MOSFET. When the on-resistance of the MOSFET is larger, for the same control IC, the over-current protection The smaller the value.

　　5. Short circuit protection

　　When the 18650 lithium ion battery 3.7vis discharging the load, if the loop current is so large that U>0.9V (this value is determined by the control IC, different ICs have different values), the control IC will judge that the load is short-circuited, and its "DO" pin will Rapidly changes from high voltage to zero voltage, causing V1 to turn from on to off, thus cutting off the discharge circuit and playing a role in short-circuit protection. The delay time of short circuit protection is very short, usually less than 7 microseconds. Its working principle is similar to overcurrent protection, but the judgment method is different and the protection delay time is also different.

　　The above describes in detail the working principle of the single-cell lithium-ion 18650 lithium ion battery 3.7vprotection circuit. The protection principle of multi-cell series lithium-ion batteries is similar and will not be repeated here. The control IC used in the above circuit is the R5421 series of Japan's Ricoh Company. In actual 18650 lithium ion battery 3.7vprotection circuits, there are many other types of control ICs, such as Japan's Seiko S-8241 series, Japan's MITSUMI's MM3061 series, Taiwan's Fujing's FS312 and FS313 series, Taiwan's Analog Technology's AAT8632 series, etc. The working principles are similar, but there are differences in specific parameters. In order to save peripheral circuits, some control ICs have filter capacitors and delay capacitors built into the chip, and their peripheral circuits can be very few, such as the S-8241 series of Japan's Seiko. In addition to the control IC, there is another important component in the circuit, which is the MOSFET. It plays the role of a switch in the circuit. Since it is directly connected in series between the 18650 lithium ion battery 3.7vand the external load, its on-resistance has a significant impact on the performance of the battery. Influence, when the selected MOSFET is better, its on-resistance is very small, the internal resistance of the 18650 lithium ion battery 3.7vpack is small, the load capacity is strong, and it consumes less power during discharge.

　　With the development of technology, the size of portable devices is getting smaller and smaller. With this trend, the requirements for the size of lithium-ion 18650 lithium ion battery 3.7vprotection circuits are getting smaller and smaller. In the past two years, control ICs and MOSFETs have appeared Products integrated into a protection IC, such as DIALOG's DA7112 series, and some manufacturers even package the entire protection circuit into a small-sized IC, such as MITSUMI's products.

Read recommendations:

186095 6000MAH 7.4V

Characteristics of electric humidifier

Lithium battery external circuit

NiMH battery packs manufacturer

401030 battery