Lithium Battery 3.7V Lithium Polymer Battery 3.2V LifePo4 Battery 1.2V Ni-MH Battery Button Coin Battery
3.7V Battery Pack 7.4V Battery Pack 11.1V Battery Pack 14.8V Battery Pack Other Battery Pack
Sino Science&Technology Battery Co.,ltd is a high-tech production enterprise which specialize in the R&D and production of Lifepo4 batteries,energy storage battery,portable UPS power supply,personalized customization lithium battery pack etc .
Environmental cylindrical 18650 21700 32700 26650 14500 18500 lithium ion rechargeable battery, LifePO4 battery,3.7V lithium polymer battery, NiMH battery , NiCD battery ,Lead acid battery,dry cell battery ,alkaline battery ,heavy duty battery, button cell battery etc. we devote to R&D,innovation ,production & sales
Shenzhen Green Power Energy Battery Co.,ltd specializes in a wide range of digital battery such as environmental cylindrical 18650 21700 32700 26650 14500 18500 lithium ion rechargeable battery, LifePO4 battery, 3.7V lithium polymer battery, NiMH battery, NiCD battery, dry cell battery, alkaline battery, heavy duty battery, button cell battery etc. we devote to R&D, innovation, production & sales. With automatic production machines we have been exported goods to all over the world over 15years. We have complete exported certificate such as KC, CE, UL, BSCI, ROHS, BIS, SGS, PSE etc
Dongguan Datapower New Energy Co.,ltd is a high-tech production enterprise which specialize in the R&D and production&sale of lithium polymer batteries,drone battery,airplane batteries &battery pack etc.
Anhui Seong-hee New Energy Technology Co.,ltd is a high-tech production enterprise which specialize in the R&D and production of primary batteries. And mainly produces and sells alkaline batteries & carbon zinc batteries. there are size AA, AAA, C, D, 9V etc
Guizhou STD Battery Co.,ltd is a high-tech production enterprise which specialize in the R&D and production & sale of lithium polymer batteries, drone battery, airplane batteries & battery pack etc.
release time:2024-07-04 Hits: Popular:AG11 battery
Analysis of the working principle of Nickel Hydride No. 5 batteries protection circuit
The circuit has overcharge protection, over-discharge protection, overcurrent protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
In the normal state, both the "CO" and "DO" pins of N1 in the circuit output high voltage, and both MOSFETs are in the on state. The battery can charge and discharge freely. Since the on-resistance of MOSFET is very small, usually less than 30 milliohms, its on-resistance has little effect on the performance of the circuit. In this state, the current consumption of the protection circuit is μA level, usually less than 7μA.
2 Overcharge protection
As a kind of rechargeable battery, lithium-ion batteries require constant current/constant voltage charging. In the initial stage of charging, constant current charging is used. As the charging process progresses, the voltage will rise to 4.2V (depending on the positive electrode material, some batteries require a constant voltage value of 4.1V), and then switch to constant voltage charging until the current becomes smaller and smaller. During the battery charging process, if the charger circuit loses control, the battery voltage will continue to be charged at a constant current after exceeding 4.2V. At this time, the battery voltage will continue to rise. When the battery voltage is charged to more than 4.3V, the chemical side reactions of the battery will intensify, causing battery damage or safety problems.
In a battery with a protection circuit, when the control IC detects that the battery voltage reaches 4.28V (this value is determined by the control IC, and different ICs have different values), its "CO" pin will change from high voltage to zero voltage, causing V2 to turn from on to off, thereby cutting off the charging circuit, making it impossible for the charger to charge the battery, and playing an overcharge protection role. At this time, due to the presence of V2's own body diode VD2, the battery can discharge the external load through the diode.
There is a delay time between the control IC detecting that the battery voltage exceeds 4.28V and sending a signal to shut down V2. The length of the delay time is determined by C3 and is usually set to about 1 second to avoid misjudgment due to interference.
3 Over-discharge protection
During the discharge process of the battery to the external load, its voltage will gradually decrease with the discharge process. When the battery voltage drops to 2.5V, its capacity has been completely discharged. If the battery continues to discharge to the load at this time, it will cause permanent damage to the battery.
During the battery discharge process, when the control IC detects that the battery voltage is lower than 2.3V (this value is determined by the control IC, and different ICs have different values), its "DO" pin will change from high voltage to zero voltage, causing V1 to turn from on to off, thereby cutting off the discharge circuit, so that the battery can no longer discharge to the load, and playing an over-discharge protection role. At this time, due to the presence of V1's own body diode VD1, the charger can charge the battery through this diode.
Since the battery voltage cannot be reduced in the over-discharge protection state, the protection circuit is required to consume very little current. At this time, the control IC will enter a low power consumption state, and the power consumption of the entire protection circuit will be less than 0.1μA.
There is also a delay time between when the control IC detects that the battery voltage is lower than 2.3V and when it sends out the V1 shutdown signal. The length of this delay time is determined by C3 and is usually set to about 100 milliseconds to avoid misjudgment due to interference.
4 Overcurrent protection
Due to the chemical characteristics of lithium batteries, battery manufacturers stipulate that the maximum discharge current cannot exceed 2C (C = battery capacity/hour). When the battery discharges at a current exceeding 2C, it will cause permanent damage to the battery or safety problems.
When the battery is discharging normally to the load, when the discharge current passes through the two MOSFETs in series, a voltage will be generated at both ends due to the on-resistance of the MOSFET. The voltage value is U=I*RDS*2, RDS is the on-resistance of a single MOSFET. The "V-" pin on the control IC detects the voltage value. If the load is abnormal for some reason, the loop current increases. When the loop current is large enough to make U>0.1V (this value is determined by the control IC, and different ICs have different values), its "DO" pin will change from high voltage to zero voltage, so that V1 turns from on to off, thereby cutting off the discharge circuit and making the current in the circuit zero, which plays an overcurrent protection role.
There is also a delay time between the control IC detecting the occurrence of overcurrent and sending the V1 shutdown signal. The length of the delay time is determined by C3, usually about 13 milliseconds, to avoid misjudgment due to interference.
In the above control process, it can be seen that the overcurrent detection value depends not only on the control value of the control IC, but also on the on-resistance of the MOSFET. When the on-resistance of the MOSFET is larger, the overcurrent protection value is smaller for the same control IC.
5 Short-circuit protection
When the battery is discharging to the load, if the loop current is large enough to make U>0.9V (this value is determined by the control IC, and different ICs have different values), the control IC will judge that the load is short-circuited, and its "DO" foot will quickly change from high voltage to zero voltage, so that V1 will turn from on to off, thereby cutting off the discharge circuit and playing a short-circuit protection role. The delay time of short-circuit protection is extremely short, usually less than 7 microseconds. Its working principle is similar to that of overcurrent protection, but the judgment method is different and the protection delay time is also different.
The above describes in detail the working principle of the single-cell lithium-ion battery protection circuit. The protection principle of multiple-cell lithium-ion batteries in series is similar and will not be repeated here. The control IC used in the above circuit is the R5421 series of Ricoh, Japan. In the actual battery protection circuit, there are many other types of control ICs, such as Seiko's S-8241 series, MITSUMI's MM3061 series, Taiwan Fujing's FS312 and FS313 series, Taiwan Analog Technology's AAT8632 series, etc. Their working principles are similar, but they differ in specific parameters. In order to save peripheral circuits, some control ICs have built-in filter capacitors and delay capacitors inside the chip, so the peripheral circuits can be very few, such as Seiko's S-8241 series. In addition to the control IC, there is another important component in the circuit, which is MOSFET. It plays the role of a switch in the circuit. Since it is directly connected in series between the battery and the external load, its on-resistance affects the performance of the battery. When the MOSFET is selected, its on-resistance is very small, the internal resistance of the battery pack is small, the load capacity is strong, and the power consumed during discharge is also small.
With the development of technology, the size of portable devices is getting smaller and smaller. With this trend, the requirements for the size of lithium-ion battery protection circuits are also getting smaller and smaller. In the past two years, products that integrate control ICs and MOSFETs into a protection IC have appeared, such as DIALOG's DA7112 series. Some manufacturers even package the entire protection circuit into a small-sized IC, such as MITSUMI's products.
Read recommendations:
Introduce the differences between batteries and fuel power cells.battery 18650 rechargeable
Next article:Nickel Hydride No. 5 battery
Popular recommendation
solar energy battery storage system Manufacturing
2023-05-10Ni-MH battery pack manufacturer
2023-03-22902030 polymer battery company
2023-03-223.2v 280ah lifepo4 battery cell
2023-03-22551235 polymer battery company
2023-03-22Ni-MH AAA400mAh 1.2V
2022-07-01Ni-MH AA1200mAh 1.2Va
2022-07-01602248 600mAh 3.7V
2022-07-01505060 2000mAh 7.4V
2022-08-19R6P
2022-12-01R14
2022-07-01Home energy storage battery GN-BOX4
2022-09-27Li-ion 26650 5000mAh 3.7V
2022-06-20Lithium Battery LQ12-150
2022-08-1918650 2400MAH 3.7V
2022-07-29LR41 battery
2023-06-2518650 battery pack 12v
2023-06-2518650 battery pack Factory
2023-06-25lifepo4 18650 battery
2023-06-25AG10 battery
2023-06-25Ternary Material Lithium-Ion Batteries
2024-12-06lithium 3400mah 3.7v 18650 battery.Precautions for lithium battery charging
2023-12-26What is the working principle of lithium batteries?
2024-09-14Lithium battery terminology, parameters, design and selection details
2024-03-28Polymer lithium battery and lithium battery difference
2024-03-19What is the difference between ternary lithium battery and lithium iron phosphate battery
2022-11-08The importance of lithium-ion battery management chips.rechargeable battery 18650 3.7v
2023-09-20the LiFePO4 battery for vehicles.lithium battery for solar energy storage system sales
2023-05-06The advantages of medical device and equipment application of lithium batteries
2023-02-1422000mAh High Muting Rate Drone Battery.energy storage battery guangdong Processing
2023-05-11